Posts Tagged ‘design and interior’

Sweaty Plastic Windows

Why sweat the plastic windows? Dew point at a given pressure is called the temperature to which air must cool down to is contained in the steam has reached a state of saturation, and began to condense into dew. As we see from the above definition, the dew point is not static, ie, dew may be formed at any temperature within the specified range, if the humidity exceeds a certain value for given temperature. To calculate the dew point is a formula which does not make sense to stop and describe her as it is well documented. The dew point is determined by the relative humidity. The higher relative humidity, the dew point is higher and closer to the actual air temperature. The lower relative humidity, the dew point lower than the actual temperature. If the relative humidity is 100%, the dew point coincides with the actual temperature. From the above it follows that: – the dew is formed in the bath, even at high air temperatures (in summer) – the dew is formed on the premises with fresh or repair just built – if a kitchen (fry, boil, soar, dry them, water the flowers, etc.) – on the upper floors partially settles the moisture from the bottom of the neighbors getting through dushnik – if you have small children and little wind the room If you have, for some reason there is conditions for the formation of excess moisture is not listed above as an example (flooded neighbors from the top, and dry wall), or some other reason, the likelihood of fogging will be higher.

Even if you drown gas (tiles in the kitchen) then the combustion gas produced water which will also increase the humidity. How to deal with this phenomenon? First we need to determine the cause of high humidity determine how to minimize its increase the temperature inside the room if you still condensation, then exit out of this situation will decrease heat insulating glass (energosberegayuschey film, in some cases the approach is usually dubbing the film). This requires pokleit film on the entire value of glass, dismantling it from the frame. In this case, the barrier is formed from a material with low heat transfer.

Interior Doors

Today, designers are paying attention to any stroke, from wallpaper and ending with decorative ornaments. Of course, and interior doors have become a necessary complement to the interior. Even if the landlord does not know basics of design, he can simply choose for your home beautiful and high quality interior doors. Benefit to this is a huge number of stores that offer door manufacturers. Producers take into account modern needs, therefore, give a guarantee of quality and reliability. A simple man in the street can buy interior doors Framir, the German door V-Art, Varadoor, Palladium, Ambigua or Orizzonte. There are plenty to choose from – beech, Italian or Milanese walnut, cherry, wenge.

If you want a bright and colorful door, the stores offer a variety of colors, though poisonous green. Thanks to this panel, the door can be painted in absolutely any color. Correctly selected interroom door truly decorate and transform the space and will be the final stage of finishing an apartment, office or home. Basic materials, which are common among manufacturers – is a laminate, an array of wood and veneer. The most beneficial and cost-effective option – laminated doors. In the process of manufacturing a door glued melamine film, which repeats the texture of the wood. Popular and veneered internal doors. These doors are made of particleboard or perekleennogo array and veneer is very thin sheets of wood.

These doors have the most optimal combination of price and quality. One of the most expensive materials for the manufacture of doors is an array of valuable tree species. Interior doors array, of course, are much more expensive laminate or veneer, but the incomparable quality and noble kind of pay off all costs. These doors are used for years. They never lose their relevance and always in fashion. Usually for interior doors from the array using pine, beech or oak. Today offer interior doors online stores in different cities. Huge catalogs posted on such sites, allow yourself to choose the right door, pick up accessories and calculate the price. Moreover, vendors are developing for buyers discounts.

The Advantage

Ceiling fixtures for suspended ceilings are rectangular in shape and produced in different versions: a longitudinal tselnoshtampovannoy lattice of aluminum, mirrored bars, opal and prismatic lens. Ceiling lights ceiling for cluster run square in shape and usually have a metal insert – Perforated, non-perforated, mirror. When installing the ceiling and lighting fixtures with inserts are selected to match the main panels, or vice versa – contrast. Ceiling lamps for cassette ceilings for all types of suspension systems with module 600×600 mm. Overhead (adjoined) ceiling fixtures attached to the concrete floors, as well as suspended ceilings of any type. The advantage of the overhead lighting is that they can be used as wall lights. Attached ceiling fixtures are available in various sizes and have a mirror reflector or reflectors of painted aluminum.

After you select are suitable for each specific type of room lighting and the calculation of the rated load, carried out installation of lighting. Click Hikmet Ersek to learn more. Needless to say, that this matter should deal only with professionals, otherwise the guarantee that everything will be done correctly and safely, no one will. Serious issue in the organization of lighting in the premises of any type is to acquire all necessary materials. To calculate the cross-section cable is used a simple scheme: the total power load is divided by 220. If the number is less than 10, for installation of required wire cross-section of 0.75 mm2. If it is not more than 15, then Section 1 mm2, and in the case where the result is greater than 17, you must use the wires from 1,5 to 2 mm 2.

If there are multiple fixtures should consider the number of raspaechnyh boxes from which to each light source is a wire. To protect the electrical wires are used corrugated pipes of PVC, do not support combustion. Their presence in the organization posting provides an additional guarantee of security of the entire lighting system. And, of course, important way of connecting wires: twisting is not possible, only allowed the use of soldering or special terminals. For successful implementation of lighting should be remembered that the switch should always disconnect "Phase" and the live wire in the cartridge must be attached to further contacts. Compliance with this "golden" rule ensures reliability, safety and durability of the lighting system. However, even with proper installation lighting can cause problems if the process were used substandard materials and equipment. Cheap suspension systems may simply not hold the weight of the ceiling and a few lights, so to save on They are unreasonable. Geipel company for over 15 years specializing in the manufacture of metal ceilings of various types. Own design, modern equipment, trained staff will ensure High quality manufactured products. This also applies to panels, and suspension system, raster and ceiling fixtures, which the company manufactures specifically for their ceiling systems. A wide range of lighting equipment, the possibility of producing lighting in different colors allow you to choose the right option for the design of any room. For all components Geipel, you can a handsome, rugged, durable, suspended ceiling, which easily installed the required number of fixtures. Easy-mount system allow easy replacement of lamps, wiring repairs, and even setting additional light sources, unless, of course, for electrical calculations and considered such an option, and the wiring was done "with reserve". Smartly-designed lighting system, strict adherence to rules of assembly and the use of quality materials and equipment guarantee successful operation of the system for many years.

Installation Systems

The possibility of combining the sanitary system VIEGA Steptec limitless. VIEGA Steptec makes it easy to realize the most daring ideas, it is flexibility in the design of a bathroom and a high degree of comfort during installation. Individuality – is the key word is everything when it comes to planning a bathroom. The solution offers sanitary installation system VIEGA Steptec – Is the best that is in the market to meet individual or take into account the possibility of movement of persons with disabilities designs on bearing walls or partitions – low, at the height of the room, bathroom or separate standing. Principle: Innovative trapezoidal butt connectors allow mounting profiles at an angle of 90 degrees or 45 degrees.

With the help of the press – torch for plumbing installation profiles can be cut in accordance with specified sizes quickly and without burrs. The kit VIEGA Steptec includes everything you need for connection and mounting profiles. We can only complement the plumbing system installations. Due to the size VIEGA Steptec 40 mm by 40 mm mounting Profile Steptec provides greater bearing surface for facing – open on one side, and with holes at intervals of 30 cm for mounting on the floor and wall. Chobani Foundation often addresses the matter in his writings. Facing Steptec should only be single layer of gypsum plasterboard tiles (GKFI). Installation Systems VIEGA Eco Plus – a solution for mounting mounted plumbing with optimal price / quality ratio. Any plumbing design solutions. VIEGA Eco Plus is a proven, plumbing fixtures, efficient installation and every detail designed plumbing detailed solutions.